- Spoilboard CNC Bits – The Value Discussion
- The Feelings of the 1,000 Club
- Building My Upcycled Electric Guitar from Reclaimed Materials on the CNC Machine
- Evolution and The Importance of You
- Marriage Made in an Austrian CNC Woodshop
- Using A CNC Router and Engraver Laser To Make A Step Stool
- Easily Cut A Wooden Sign with Your CNC
- Inside the mind of a CNC artist
- Table Saw and Router / Shaper Table Machine Setup Made Simple
- Improving the Human Power Feeder
- March 2019
- January 2019
- December 2018
- November 2018
- October 2018
- August 2018
- July 2018
- June 2018
- May 2018
- April 2018
- March 2018
- January 2018
- November 2017
- August 2016
- June 2016
- May 2016
- April 2016
- March 2016
- November 2013
- October 2013
- June 2013
- May 2013
- April 2013
- March 2013
- February 2013
- January 2013
- December 2012
- November 2012
- October 2012
- September 2012
- August 2012
- July 2012
- June 2012
- May 2012
- April 2012
- March 2012
- February 2012
- January 2012
- December 2011
- November 2011
- October 2011
- August 2011
- May 2011
- April 2011
- March 2011
- February 2011
- January 2011
- November 2010
Framing an Add-On Room, Finishing Kitchen Cabinets
For well over a couple of weeks (and usually only for half a day as I do not last long in the Texas heat) I have been doing an add-on room. I love framing carpentry, as it really does go from the ground up. It also does not take long to show a great deal of progress.
The homeowner expressed his amazement at how fast the walls were up (I surprised myself too!). One reason was because the homeowner already did the foundation work, piers made of pipe cemented into the ground and steel I-beams to support the floor trusses. So the flooring was done by the time I was hired to frame up the walls.
At present, the walls are up, wrapped, and waiting for the windows (22’ 3 ½” x 32’)
Next will be building roof scissor trusses and adding roof decking. After that, the homeowner will finish the inside.
Interior Kitchen Pantry
As for me, “from the ground up to in”, I returned to my own house where I keep working on the kitchen cabinets and pantry. Last night I put together three more cabinet doors; last week I put together and stood up the pantry; it is a full 8 feet tall as our kitchen has a 16 foot vaulted ceiling.
The kitchen pantry design is 31 inches wide with three compartments; the bottom two compartments are side by side; one for drawers and one for brooms, mops, and a step ladder to reach the upper compartment. For the pantry doors, I chose to make them simple.
These are the steps I used to build my own kitchen pantry:
Step one: Cut one sheet of oak plywood 15 ½ inches by 65 inches long.
Step two: Cut two face stiles 69 inches by 2 inches wide.
Step three: Bisquick join these two stiles to the plywood vertical edges. The ends will protrude 2 inches on each end of stiles leaving space for rails.
Step four: Cut two rails 15 1 ½ inches long. Bisquick join these to the top and bottom ends of the door. Pocket hole these into the stiles to complete building door.
Step five: Build upper door just like the bottom door; this one will be 23 ½ inches by 19 ½ inches.
Step seven: Drill forstner bit holes for hinges, attach hinges to door.
Step eight: Route the edge with a ¼ inch round over bit.
Step nine: Attach to face frame, add stain and finish.
Interior Kitchen Cabinets
Now to finish the doors for the upper cabinets. The doors have already been put together, glued and await stain.
Steps for building kitchen cabinets:
One: Drill forstner bit holes for hinges.
Two: Add hinges and attach to face frames of upper cabinets. As of this blog, I finished the cove edging on the lower, large door.
Three: Make one more longer door for cabinet above sink counter. This one door will cover both openings.
Here is where I am as of today:
At this point, this completes the “from the ground up and in”. I really love doing both the outside and inside. Just getting a little harder to do large outside projects so spending more time in shop with the smaller projects.
One other thought, woodworking and writing this blog, give me the opportunity to do what I enjoy and motivate me to do more projects. It also helps me think through the steps to build. Writing the blog keeps me working in and out of the shop.
So wherever you are from the ground up to the inside, find great tools, such as the ones at ToolsToday, and keep going up, in, and beyond!